题目
英语翻译
1)C/L偏移:
1、客户图纸上面焊盘部位长度没有数据,数据测量时没有进行管控;
2、覆盖膜开窗是切割机切割出来,切割窗口完成后需要进行二钻定位孔,二钻定位孔是切割出来,切割时定位孔容易出现撕裂或者不圆等现象,贴附时导致覆盖膜定位孔对制品孔对不齐,导致开窗偏移,即出现C/L偏移.
2)短路:
1.打样时因数量少作业员手工开料,由于基材薄,开料后产品有些折皱,导致曝光时出现曝光不良,DES后形成短路现象.
2.样品打样交期紧,当时测试治具没有制作回来,所以敝司暂定要求FQC检验员在40X显微镜下对线路进行100%开短路检验,因检查员不仔细未发现导致不良漏检流出
3.流出原因:
检查员不仔细未发现导致不良漏检流出.
4.发生对策 :
1)C/L偏移:
1.发现覆盖膜开窗偏移大的产品需要测数确认,超出公差范围的产品报废处理;
2.量产时开钢模可以完全避免此现象发生.
2)短路:
1.对开料工序作出要求,样品无论数量多少,都要使用机器开料,确保基材平整度.
2.电测治具已经OK,量产时通过电测治具对开短路进行测试,可以彻底避免此不良流出;
5.流出对策:
1.客诉不良对FQC检验员进行培训,同时后续所有的样品检查FQC固定2人专门对应.
1)C/L偏移:
1、客户图纸上面焊盘部位长度没有数据,数据测量时没有进行管控;
2、覆盖膜开窗是切割机切割出来,切割窗口完成后需要进行二钻定位孔,二钻定位孔是切割出来,切割时定位孔容易出现撕裂或者不圆等现象,贴附时导致覆盖膜定位孔对制品孔对不齐,导致开窗偏移,即出现C/L偏移.
2)短路:
1.打样时因数量少作业员手工开料,由于基材薄,开料后产品有些折皱,导致曝光时出现曝光不良,DES后形成短路现象.
2.样品打样交期紧,当时测试治具没有制作回来,所以敝司暂定要求FQC检验员在40X显微镜下对线路进行100%开短路检验,因检查员不仔细未发现导致不良漏检流出
3.流出原因:
检查员不仔细未发现导致不良漏检流出.
4.发生对策 :
1)C/L偏移:
1.发现覆盖膜开窗偏移大的产品需要测数确认,超出公差范围的产品报废处理;
2.量产时开钢模可以完全避免此现象发生.
2)短路:
1.对开料工序作出要求,样品无论数量多少,都要使用机器开料,确保基材平整度.
2.电测治具已经OK,量产时通过电测治具对开短路进行测试,可以彻底避免此不良流出;
5.流出对策:
1.客诉不良对FQC检验员进行培训,同时后续所有的样品检查FQC固定2人专门对应.
提问时间:2021-03-05
答案
1)C/L偏移:
1) C/L migration:
1、客户图纸上面焊盘部位长度没有数据,数据测量时没有进行管控;
1 and customer's drawing pad parts above length no data, data measured not control;
2、覆盖膜开窗是切割机切割出来,切割窗口完成后需要进行二钻定位孔,二钻定位孔是切割出来,切割时定位孔容易出现撕裂或者不圆等现象,贴附时导致覆盖膜定位孔对制品孔对不齐,导致开窗偏移,即出现C/L偏移.
2, covering membrane window is cutting machine cutting out after completion, cutting window need for two, two drill holes drilled positioning is cutting out, positioning hole during cutting positioning hole prone to rent or not round etc. Phenomenon, attached with a lead to coverage of membrane positioning hole to not neat, products hole that led to open the window migration, appear C/L migration.
2)短路:
2) short-circuit:
1. 打样时因数量少作业员手工开料,由于基材薄,开料后产品有些折皱,导致曝光时出现曝光不良,DES后形成短路现象.
1. When less homework because of quantity salesman manual opens the material, because members backing thin, opens the material products, leading to expose some wrinkles appear after exposure bad, DES formed short-circuit phenomenon.
2.样品打样交期紧,当时测试治具没有制作回来,所以敝司暂定要求FQC检验员在40X显微镜下对线路进行100%开短路检验,因检查员不仔细未发现导致不良漏检流出
2. Sample proofing delivery tight, then test fixture did not make back, so our company 40X provisionally requirements under microscope in FQC inspectors to open the lines, for 100% short-circuit test that causes not carefully inspectors, adverse undetection outflow
3. 流出原因:
3. Outflows reasons:
检查员不仔细未发现导致不良漏检流出.
Inspector without careful not found that lead to bad undetection outflow.
4. 发生对策 :
4. Happen countermeasures:
1)C/L偏移:
1) C/L migration:
1.发现覆盖膜开窗偏移大的产品需要测数确认,超出公差范围的产品报废处理;
1. Find indusium window offset big products need to test several confirmation, beyond the tolerances products rejected processing;
2.量产时开钢模可以完全避免此现象发生.
2. When open mass production to completely avoid the steel mold phenomenon.
2)短路:
2) short-circuit:
1.对开料工序作出要求,样品无论数量多少,都要使用机器开料,确保基材平整度.
1. Commuting requirements, material process make sample regardless of the quantity, want to use the machine to ensure open material base material smoothness.
2. 电测治具已经OK,量产时通过电测治具对开短路进行测试,可以彻底避免此不良流出;
2. Electrical measurement fixture has OK, mass production by electrical measurement when opening fixture short-circuit test, can completely avoid the bad outflow;
5.流出对策:
5. Outflows countermeasures:
1. 客诉不良对FQC检验员进行培训,同时后续所有的样品检查FQC固定2人专门对应.
1. Poor aftersale inspectors to FQC trained, and subsequent all samples check FQC 2 special fixed position.
1) C/L migration:
1、客户图纸上面焊盘部位长度没有数据,数据测量时没有进行管控;
1 and customer's drawing pad parts above length no data, data measured not control;
2、覆盖膜开窗是切割机切割出来,切割窗口完成后需要进行二钻定位孔,二钻定位孔是切割出来,切割时定位孔容易出现撕裂或者不圆等现象,贴附时导致覆盖膜定位孔对制品孔对不齐,导致开窗偏移,即出现C/L偏移.
2, covering membrane window is cutting machine cutting out after completion, cutting window need for two, two drill holes drilled positioning is cutting out, positioning hole during cutting positioning hole prone to rent or not round etc. Phenomenon, attached with a lead to coverage of membrane positioning hole to not neat, products hole that led to open the window migration, appear C/L migration.
2)短路:
2) short-circuit:
1. 打样时因数量少作业员手工开料,由于基材薄,开料后产品有些折皱,导致曝光时出现曝光不良,DES后形成短路现象.
1. When less homework because of quantity salesman manual opens the material, because members backing thin, opens the material products, leading to expose some wrinkles appear after exposure bad, DES formed short-circuit phenomenon.
2.样品打样交期紧,当时测试治具没有制作回来,所以敝司暂定要求FQC检验员在40X显微镜下对线路进行100%开短路检验,因检查员不仔细未发现导致不良漏检流出
2. Sample proofing delivery tight, then test fixture did not make back, so our company 40X provisionally requirements under microscope in FQC inspectors to open the lines, for 100% short-circuit test that causes not carefully inspectors, adverse undetection outflow
3. 流出原因:
3. Outflows reasons:
检查员不仔细未发现导致不良漏检流出.
Inspector without careful not found that lead to bad undetection outflow.
4. 发生对策 :
4. Happen countermeasures:
1)C/L偏移:
1) C/L migration:
1.发现覆盖膜开窗偏移大的产品需要测数确认,超出公差范围的产品报废处理;
1. Find indusium window offset big products need to test several confirmation, beyond the tolerances products rejected processing;
2.量产时开钢模可以完全避免此现象发生.
2. When open mass production to completely avoid the steel mold phenomenon.
2)短路:
2) short-circuit:
1.对开料工序作出要求,样品无论数量多少,都要使用机器开料,确保基材平整度.
1. Commuting requirements, material process make sample regardless of the quantity, want to use the machine to ensure open material base material smoothness.
2. 电测治具已经OK,量产时通过电测治具对开短路进行测试,可以彻底避免此不良流出;
2. Electrical measurement fixture has OK, mass production by electrical measurement when opening fixture short-circuit test, can completely avoid the bad outflow;
5.流出对策:
5. Outflows countermeasures:
1. 客诉不良对FQC检验员进行培训,同时后续所有的样品检查FQC固定2人专门对应.
1. Poor aftersale inspectors to FQC trained, and subsequent all samples check FQC 2 special fixed position.
举一反三
已知函数f(x)=x,g(x)=alnx,a∈R.若曲线y=f(x)与曲线y=g(x)相交,且在交点处有相同的切线,求a的值和该切线方程.
我想写一篇关于奥巴马的演讲的文章,写哪一篇好呢?为什么好
奥巴马演讲不用看稿子.为什么中国领导演讲要看?
想找英语初三上学期的首字母填空练习……
英语翻译
最新试题
- 1自然环境和人文特征
- 2fab 什么意思
- 3(探索题)某家庭装饰厨房需用480块某品牌的同一种规格的瓷砖,装饰材料商店出售的这种瓷砖有大,小两种包装,大包装每包50片,价格为30元;小包装每包30片,价格为20元,若大,小包
- 4六边形ABCDEF,AB=DE,BC=EF,CD=FA,∠A=∠D,求证,∠C=∠F
- 5在桃花源记中,写桃花林美景的句子
- 6请解释炉火正旺时,加入湿煤会燃烧更旺的原因
- 7窃读记里“你们是吃饭长大的,也是读书长大的!”前后照应的句子是什么?
- 8关于和同学合作的英语作文 300字 初四水平.急用
- 9为什么说隋炀帝创立进士科标志着科举制的成立?
- 10take a seat______ take a chance________ take a walk________
热门考点
- 1水果店一批货物,第一天买了60千克,正好是第二天买的3分之2,两天共卖了全部的4分之1,原有几千克 解方程
- 2形容人长得丑的成语
- 3托运玻璃仪器360箱合同规定每箱20元若有损坏的不仅不给运费还要赔100元运算后想获得运费最多只能坏多少箱
- 4课文紫藤萝瀑布中提到那种紫藤萝花,它们各自的特点是什么
- 5一个三角形中最少有几个锐角,最大的角应不小于几度
- 6the park near the building is very beautiful.
- 7“不”下面加一个“要”是什么字求大神帮助
- 8求一个左右结构的字,左边一个香右边一个尼
- 9The little boy ( ) tom.
- 10sin四分之派cos四分之派的值为?